User:Vincecate/WaterWalker

Description

The idea is to have a very wide base, like 150 feet, so that you do not tip much in the waves. This is basically a tripod with balls for floats on each of the 3 legs. There is also a string to keep the legs from moving out further. The living area would be below where the weights are in the model in the center.

Detail

• Material issues - plastic for the balls, aluminum, steel, or wood for the compression members. These might be truss or pipe shapes.
• Tension members could be plastic rope or steel cable
• Would use kite and sea anchor for movement on migration

Energy Generation and Storage

If we had 6 legs instead of 3 as in the model and let the legs flex up and down, we could use that motion to drive pumps that pumped air into the balls. Then we could run a propeller or generator from the compressed air.

Requirements Analysis

• Safety
  • It is very wide compared to boats and so should be very stable
  • No active ballast controls so no chance of that going wrong

• Comfort
  • Should have a gentle motion on normal days but significant response to large waves.

• Cost
  • This should be one of the cheapest designs. It's very simple. Although it is as wide as a large cruise ship, most of the area is just cables over open space.

• Pretty
  • Looks nice. Could have walkways going down to each of the 3 balls and a platform and big umbrella on each. Could be very pretty.

• Modular
  • Can make individual family sized units. Could have cable under a line of these so they floated together if you connected a sea anchor at one end and a large kite at the other.

• Cargo
  • Since it floats up and down with waves like a boat, should be reasonable to dock a boat next to it. Probably have a small dock mounted on the wall so it could float up and down a bit relative to the wall. Need a walkway from house to where boat will dock.

• Free Floating
  • Yes, could anchor also.

• Scalable
  • Scales up or down in size (height, diameter).

• Standards

• Mobile
  • Could be made to fold up with balls detaching or come apart with each leg and ball as a separate unit. Then it

could be transported by truck or barge easily.

• Draft
  • Very shallow draft.

Video of 6-foot model

In the model the 1/2 inch wood dowels are 4 feet long, so would be 100 feet in a full scale model. From the edge of one ball to another is about 6 feet. The tests below are with 6 lbs but it might be interesting to try 10 lbs so the balls were more underwater. Note that each 1 lb in the model is over 15,000 lbs in full scale.

The balls are a bit over 6 inches, so over 12.5 feet in full scale. In the videos below the wind driven waves are around 6 inches, so around 12.5 feet in full scale. There is also a swell from far away which can go up and down a couple feet.

These videos are slowed by 4 but should really be slowed by 5 since 1:25 scale.

<youtube v="RWY7mcRwg8g" />

From down on the side of the pier.

<youtube v="7sEPFt8JS7Y" />

Also from the side of the pier.

<youtube v="YNbmb0vLN9g" />

Shot from the top of the pier at the end of the pier.

Aquaculture

You could have net under the whole structure, attached to the 3 corners, to make a place for aquaculture. Fresh water fish farms use automatic feeders where the fish bump something and then get a piece of food. With these no food is wasted. Don't know if salt water farms use these but I expect they could.

One possible problem is that moving through the water would be harder with a big net underwater.

Future Models

I think 3 telephone poles could be used to make a prototype. I could make the balls out of foam and then cover them with fiberglass/apoxy.

More Pictures

Vince lowering model into the water from steps. Note that when there is no tension on the strings (really weed wacker line) they are not straight.

Top view with steps for scale. Note fishing line that is used to pull it back in.

Side view. Floating just fine with 6 lbs on it. At about 8 lbs the balls would be half in the water. Might be interesting to try other weights.

Of course we had tested the 6 lbs back at home and knew it would work just fine. Well, we tested 1/3rd and extrapolated.

All done and heading back up the steps to the top of the Santa Cruz Pier. Part of why I built this model was because it was easy to fold up and put in a trunk. Larger versions could be put on a flatbed truck, which would not be possible with some designs.

View of the Santa Cruz Pier after we went to play on the beach.

At the Seasteading Conference we put the model into the pool. It still worked.