Difference between revisions of "User:Vincecate/BallHouse"

From Seasteading
Jump to: navigation, search
(Full Scale Ball House in Plastic)
(Low Cost Design Champ)
 
(79 intermediate revisions by the same user not shown)
Line 4: Line 4:
  
  
Idea is to use a ball shape with [[HangingBallast]] to stabilize it.  There would be four or more ropes going to a single ballast well below the ball.   With a 30 foot diameter ball you could have two good floors and extra storage space.  Should be enough for a family.  This is probably about the lowest cost structure with enough space that is  still safe on the open ocean.   
+
Idea is that a ball shape seems to ride waves really well and provide the best internal volume to surface area ratio possible.  A ball shape is strong structurally.   With a 30 foot diameter ball you could have two good floors and extra storage space.  Should be enough for a family.  This is probably about the lowest cost structure with enough space that is  still safe on the open ocean.  This is very much like [[User:Vincecate/GeodesicVessel]] but with no stability from the shape of the structure.  This really needs something to stabilize it.
  
This is very much like [[User:Vincecate/GeodesicVessel]] but with no stability from the shape of the structure. This really needs a hanging ballast.
+
One way to stabilize the ball is with a [[HangingBallast]].  There would be ropes going to a single ballast well below the ball (like 500 feet below). 
 +
 
 +
Another way to stabilize the ball is the way [[Life_rafts]] do with a water ballast under it.  This is just something that traps a bunch of water.  The mass of water provides more inertia so that waves can not tip the ball as easily.   This should provide a very smooth ride.  It also avoids the problems of having to raise and lower the hanging ballast to come near land.  So it is probably better.
  
 
==Internal==
 
==Internal==
Line 15: Line 17:
 
==Materials==
 
==Materials==
  
If we could make a form for concrete or plastic this could be really cheap.  In Anguilla they make forms for poring cisterns where the two sides of the form are connected together by pieces of metal which stay in the concrete.  There is a way these are released from the form so the form can be taken off.  I think a similar thing could be done to make a 30 foot ball mold work.  If so this could be crazy cheap, like $100,000.
+
If we could make a form for concrete or plastic this could be really cheap.  In Anguilla they make forms for poring cisterns where the two sides of the form are connected together by pieces of metal which stay in the concrete.  There is a way these are released from the form so the form can be taken off.  I think a similar thing could be done to make a 30 foot ball mold work.  If so this could be crazy cheap.
 +
 
 +
Some size ball could be made using rotomold methods, not sure what limits there are on how thick or how large an object could be made this way.
 +
 
 +
Molded plastic or aluminum pieces, or steel or aluminum plates, could be make to approximate a sphere using some interesting geometric shapes. 
 +
 
 +
* [http://en.wikipedia.org/wiki/Triacontahedron Triacontahedron] - 30 rhombic faces
 +
* [http://en.wikipedia.org/wiki/Pentakis_dodecahedron Pentakis dodecahedron] - 60 identical triangles
 +
* [http://en.wikipedia.org/wiki/Pentagonal_hexecontahedron Pentagonal hexecontahedron] - 60 identical faces
 +
* [http://en.wikipedia.org/wiki/Bucky_ball#Buckyballs Bucky ball / soccer ball] - 12 pentagons and 20 hexagons of same edge length
 +
* 180 triangles - like soccer ball but with pentagons replaced by 5 triangles and hexagons replaced by 6 triangles
 +
* [http://www.plunk.org/~grantham/public/geodesic_domes/geodesic_domes.html other sizes like 80 triangles] and [http://desertdomes.com other geodesic domes] but not always uniform sized triangles
  
Steel or aluminum plates could be done with triangles making a geodesic shape.
+
These might be for prototypes, production vehicles, or for molds to make prototypes or production vehicles.  Pieces might be welded or bolted together.
  
==Expendable porch==
+
==Living space above the sphere==
  
There would be a small concrete entry building on top.  Around this could be a wood porch that people would not stay on during a storm.  In Anguilla people build simple wood restaurants right on the edge of the beach and just quickly rebuild them if they are destroyed in a hurricaneThe wood could also support solar panelsThese would be taken inside before a storm.  Would use [[User:Vincecate/Migration]] to minimize the chance of storms.
+
Like in [[User:Jesrad/BunkerStead|BunkerStead]] it would be nice to have some living space that was above the sphere and had lots of windows.  I would probably have it close to the top of the sphere thoughModel tests show that even the top of the sphere should be very safe from the waves.  However, people would clearly go below if there was a storm that seemed dangerousMight fold in/roll-up/take-down some stuff if there was a bad storm comingWind or wind blown spray from a wave might be able to damage things.  Would use [[User:Vincecate/Migration]] to minimize the chance of storms.
  
 
==Other==
 
==Other==
Line 63: Line 76:
  
 
* Draft
 
* Draft
** Very shallow draft for a seastead if the hanging ballast is winched up.  If the waves were small as you approached a harbor it should be safe to winch up the hanging ballast.  Could lower the ballast onto the bottom in the harbor.  If the ballast could be split into 4 or more pieces it could be stable like a tension leg structure when parked in shallow water.
+
** Very shallow draft for a seastead if the hanging ballast is winched up.  If the waves were small as you approached a harbor it should be safe to winch up the hanging ballast.  Could lower the ballast onto the bottom in a harbor, keeping some tension, making a simple tension-leg structure.
  
 
==Experiments==
 
==Experiments==
  
Used a 36 cm (14.2 inch) diameter buoy with 20 lbs of steel weights.  At 1:25 scale this is about a 30 foot sphere.  This video should have been slowed down by a factor of 5 but is really slowed down by a factor of 4.   
+
[[Image:Ballhousemodel.jpg]]
 +
[[Image:Ballinfo.JPG]]
 +
 
 +
Used a 36 cm (14.2 inch) diameter buoy with 20 lbs of steel weights.  At 1:25 scale this is about a 30 foot sphere.  These videos should have been slowed down by a factor of 5 but are really slowed down by a factor of 4.   
 +
 
 +
The first video is with about 4 feet of rope in waves that are a few inches (6 inches simulates 12.5 feet).  This was shot [http://maps.google.com/?ie=UTF8&t=h&ll=18.257062,-63.001608&spn=0.002175,0.003455&z=18 near the end of the pier in Island Harbor Anguilla].  This swings back and forth too much.  Experiments on later days with longer ropes work much better.
  
The first video is with about 4 feet of rope.
 
 
<youtube v="u6U8tc7wp2s" />
 
<youtube v="u6U8tc7wp2s" />
  
The video below is with the 20 lbs of weight tied close below the ball, in big waves. The biggest waves could be simulating 50 foot waves, which is bigger than I expect to ever see if we use migration.
+
==Experiments 2 - deep water in Shoal Bay==
 +
 
 +
The next 4 videos were shot on Aug 28, 2008 after swimming to [http://maps.google.com/?ie=UTF8&t=h&ll=18.258779,-63.028715&spn=0.008701,0.013819&z=16 deep water on the other side of the inner reef at shoal bay]. I estimate the biggest waves are simulating 50 foot waves, which is bigger than I expect to ever see if we use migration.
 +
 
 +
The first video below is with the 20 lbs of weight tied close below the ball, maybe 1/2 foot of rope.
  
 
<youtube v="8Ad1lzixLfg" />
 
<youtube v="8Ad1lzixLfg" />
  
The video below is with about 25 feet of rope between the ball and the 20 lbs, in the same big waves as the above video.
+
The rest of the videos on this day are with 23 feet of rope between the ball and the 20 lbs, in the same big waves as the video above.
  
 
<youtube v="HqZY7LYdLHk" />
 
<youtube v="HqZY7LYdLHk" />
 +
 +
During this next video I was drifting closer to shallow water so stopped early.  There are a couple times when the ball seems to tilt a bit.  It may be because the weights had touched bottom and the tension on the rope was reduced.  But either way, this ball is still doing a good job of keeping the topside up in really large waves.
 +
 +
<youtube v="TUUmPPDn_j0" />
 +
 +
This next shot is fun because there is a jellyfish in the upper-right part of the shot.  It is also interesting because in about the middle of the clip we get the underwater view of a breaking wave hitting and tipping the model.
 +
 +
<youtube v="fd_9ry_oJXI" />
 +
 +
==Experiments 3 - deep water outside Island Harbor==
 +
 +
The videos in this section were shot from a kayak on Aug 31, 2008.  I took the net off the buoy and put some black lines on to make it easier to see how much the buoy tips with the waves.  These were shot [http://maps.google.com/?ie=UTF8&t=h&ll=18.262589,-63.003137&spn=0.008701,0.013819&z=16 outside the reef north of Island Harbor Anguilla].  The kayak rudder does not work when you are nearly standing still so peddling did not work so well.  I could not use the paddle while keeping the camera aimed, so that was not good either.  I tried giving my 4 year old the camera, but in hindsight, I should have explained the goal of keeping near the buoy and had him use the paddle while I did the camera.  Anyway, these are mostly not close enough to see how well my water-level with a new block inside to dampen the sloshing is working, but sometimes.  I have since realized that I could take apart the paddle and use half in one hand as an oar to control my direction while my legs provided power.  So I think I can stay closer to the model next time.
 +
 +
I would call these simulated 40 foot waves, which is more than I think we will see if we use migration.  Used the same 23 foot rope used in the Shoal Bay experiments.
 +
 +
<youtube v="GepQjK4uVJ8" />
 +
 +
<youtube v="lMhj77_fkW8" />
 +
 +
<youtube v="ZtL4JhVIEzY" />
 +
 +
In this next video we got close enough at times to really see the red water moving around.  Even though the buoy is staying very level, the waves are accelerating it sideways and so causing the red water to move around.  Now these are simulated hurricane conditions, and not normal weather.  If you were in a small bunk with sides on it or in a seat with a seatbelt, you would be fine.
 +
 +
<youtube v="_0_ph-K-lL8" />
 +
 +
This next video was shot by Teryn, my 4-year-old, while sitting on the front of my kayak.  The a lightweight boy on the front moves up and down more than a big dad in the middle.  But it is still interesting.
 +
 +
<youtube v="pQ3iqbJwt3g" />
  
 
==Full Scale Ball House in Plastic==
 
==Full Scale Ball House in Plastic==
  
I think it would be reasonable to make a 30 foot ball out of HDPE plastic.  If this has "carbon black" in it the sun won't hurt it.  I am thinking that if the plastic was 1 inch thick it would be plenty strong enough.  A ball is a strong shape as the sides sort of have arch type support in both directions.
+
I think it would be reasonable to make a 30 foot ball out of [http://en.wikipedia.org/wiki/High_density_polyethylene HDPE plastic].  If this has "carbon black" in it the sun won't hurt it.  I am thinking that if the plastic was 1 inch thick it would be plenty strong enough.  A ball is a strong shape as the sides sort of have arch type support in both directions.  Think of how strong an egg is when you try to squeeze it in your hand.
  
 
The density of HDPE plastic is just under that
 
The density of HDPE plastic is just under that
of water.  I think this plastic is about $1/lb.  So a 30 foot ball that was 1 inch thick might weigh about 15,000 lbs and cost about $15,000.
+
of water.  If you buy the HDPE pellets by the ton, the price is about $1/lb.  So a 30 foot ball that was 1 inch thick might weigh about 15,000 lbs and cost about $15,000 for the raw plastic.  It may even be that 1/2 inch is thick enough.  
 
This would be a very low cost seastead.
 
This would be a very low cost seastead.
  
Line 92: Line 141:
 
Then you plug the holes in the ball with HDPE plugs (fusion weld these in).
 
Then you plug the holes in the ball with HDPE plugs (fusion weld these in).
  
Another possibility is related to how they wind on the plastic for large corrugated plastic pipe.  We could go around and
+
Another possibility is related to how they [http://www.youtube.com/watch?v=he6A9LQU7Lc wind on the plastic for large corrugated plastic pipe].  We could go around and
 
around making a ball instead of a pipe.  Maybe we put on a two inch wide strip of plastic each time we go around.  Might take a machine most of a day to make a ball but this is not bad.
 
around making a ball instead of a pipe.  Maybe we put on a two inch wide strip of plastic each time we go around.  Might take a machine most of a day to make a ball but this is not bad.
  
My favorite way is to have a big ball "rotomold" out of aluminum.  This aluminum ball would be mounted on some wheels so it could be rolled in different directions.  Imagine a truck upside down with the ball on the 4 wheels.  If the truck turns left and right the ball will be rolled in different directions (don't think I would really use a truck, probably 3 or 4 wheels with 1 or 2 that can turn and electric motor on one or more).  If we heat up the mold, put in the HDPE pellets, and roll the mold while it cools down we can have a big plastic ball when it is done.  This "rotomolding" is how most kayaks are made.  Then the mold would have to come apart in sections so we could get the plastic ball out.
+
My favorite way is to have a big ball [http://en.wikipedia.org/wiki/Rotomold rotomold] out of aluminum.  This 30-foot aluminum ball would be set on some wheels so it could be rolled in different directions.  Probably 3 or 4 wheels with 1 or 2 that can turn and an electric motor on one or more.  If we put the HDPE pellets inside, start rolling the mold, heat it up, and keep rolling the mold while it cools down we can have a big plastic ball when it is done.  This "rotomolding" is how most [http://www.youtube.com/watch?v=0XW_0Ngizog kayaks are made] so easily that they can [http://www.amazon.com/Pelican-Pursuit-Kayak-%252d-10%2592/dp/B000E178UU/ref=pd_bbs_4?ie=UTF8&s=sporting-goods&qid=1220165176&sr=8-4 sell as little as for $240]The mold would have to come apart in sections so we could get the plastic ball out.
 +
 
 +
Looking for large roto-mold examples I found [http://www.advancedtanktechnologies.com Ace Roto-mold/ Advanced Tank Technologies] makes [http://www.advancedtanktechnologies.com/products/?p=productsMore&iProduct=92&sName=vertical-tanks tanks up to 10,500 gallons] which is 142 by 177 inches (14.75 feet).  Found a [http://www.tradeindia.com/selloffer/1347609/Rock-N-Roll-Machine.html Rock-N-Roll machine] that can do 6.5 meter boats (21 feet).
 +
 
 +
There is [http://allroto.com info about roto-molding online].
 +
 
 +
There are lots of places that sell [http://www.sculpturespaces.com/pro.php?fl1=Space%20Art&fl2=Stainless%20Steel%20Sphere stainless steel spheres or hemispheres] that could be used for molds.  Shipping gets hard above 8 feet diameter, but they can be made whatever size you want it seems.  With two hemispheres you could make plastic balls using the rotomold method (though some work will need to be done to figure out how to heat and roll the mold).  Could start plastic ball making experiments using 12-inch steel hemispheres from [http://shopwagner.com shopwagner.com] for $37 each.
 +
 
 +
==Full Scale Using Ductal==
 +
 
 +
The [[Ductal]] concrete blend is very strong, waterproof, and lasts well in salt-water.  This could work well for making a larger model or full scale BallHouse.
 +
 
 +
==Low Cost Design Champ==
 +
 
 +
The ball does not heave up and down like the pipes/cylinders/spars do so it would not require [[heave]] plates.  Having the ballast rope attach to the bottom of the ball provides enough stability, no truss is required.  The experiments show that this design does well even in 50 foot waves.  A ball shape is strong for the amount of material, whatever that is: plastic, concrete, aluminum, or steel.  So I think for small single family seasteads that are safe on the open ocean that this is the low cost design champ.  If you think there is anything cheaper please post in the discussion for this page or on the Engineering forum.
 +
 
 +
I think this ball could even be made smaller, like 20 feet diameter, or even 15 feet diameter, and still be very stable and safe.  Because it floats up with the waves, and moves away and so kills breaking waves, it can be safe in waves higher than it is.  It would be easier to get plastic to work for a 15 foot diameter ball than a 30 foot diameter ball.  The internal volume would still be better than many boats people live on.  At this size it could be cheaper for a family to buy a Ball House than to pay to be smuggled into the USA.
 +
 
 +
==Chinese Survival Pods==
 +
 
 +
Some Chinese worried by the movie 2012 [http://rt.com/news/apocalypse-china-survival-pods-004/ built ball shaped survival pods].  These were for sale for $50,000 before the Mayan end of calendar and one expects much cheaper after that.
 +
 
 +
==Discussion on Forum==
  
Looking to see how large a plastic ball I can find I see [[http://www.complexplastics.com/ a 90 in ball].
+
This proposal has been [http://seasteading.org/interact/forums/engineering/structure-designs/ball-house discussed on the forum].

Latest revision as of 10:36, 14 December 2012


Idea

Idea is that a ball shape seems to ride waves really well and provide the best internal volume to surface area ratio possible. A ball shape is strong structurally. With a 30 foot diameter ball you could have two good floors and extra storage space. Should be enough for a family. This is probably about the lowest cost structure with enough space that is still safe on the open ocean. This is very much like User:Vincecate/GeodesicVessel but with no stability from the shape of the structure. This really needs something to stabilize it.

One way to stabilize the ball is with a HangingBallast. There would be ropes going to a single ballast well below the ball (like 500 feet below).

Another way to stabilize the ball is the way Life_rafts do with a water ballast under it. This is just something that traps a bunch of water. The mass of water provides more inertia so that waves can not tip the ball as easily. This should provide a very smooth ride. It also avoids the problems of having to raise and lower the hanging ballast to come near land. So it is probably better.

Internal

The geodesic shape should mean you don't need as much, or maybe any, internal bracing. This can open up the inside space and make it cheaper to build.


Materials

If we could make a form for concrete or plastic this could be really cheap. In Anguilla they make forms for poring cisterns where the two sides of the form are connected together by pieces of metal which stay in the concrete. There is a way these are released from the form so the form can be taken off. I think a similar thing could be done to make a 30 foot ball mold work. If so this could be crazy cheap.

Some size ball could be made using rotomold methods, not sure what limits there are on how thick or how large an object could be made this way.

Molded plastic or aluminum pieces, or steel or aluminum plates, could be make to approximate a sphere using some interesting geometric shapes.

These might be for prototypes, production vehicles, or for molds to make prototypes or production vehicles. Pieces might be welded or bolted together.

Living space above the sphere

Like in BunkerStead it would be nice to have some living space that was above the sphere and had lots of windows. I would probably have it close to the top of the sphere though. Model tests show that even the top of the sphere should be very safe from the waves. However, people would clearly go below if there was a storm that seemed dangerous. Might fold in/roll-up/take-down some stuff if there was a bad storm coming. Wind or wind blown spray from a wave might be able to damage things. Would use User:Vincecate/Migration to minimize the chance of storms.

Other

Should be very strong, very stable, very safe, and not very costly for the amount of living space.

Could use small strong glass to make portals to let some light in and let people see out some.

The heavy things like batteries should be at the very bottom of the inside space (say below a flat internal floor).

Requirements Analysis

  • Safety
    • As long as the hanging ballast stays on it should stay upright
  • Comfort
    • Should have a gentle motion on normal days but significant response to large waves.
  • Cost
    • Hard to imagine anything cheaper than this that has this much space and is safe in the open ocean.
  • Pretty
    • Sometimes functional things start to look nice after awhile. And not every one can afford pretty houses.
  • Modular
    • Can make individual family sized units. Could have cable under a line of these so they floated together if you connected a sea anchor at one end and a large kite at the other. Each module could connect to the big cable at its hanging ballast.
  • Cargo
    • Since it floats up and down with waves like a boat, should be reasonable to dock a boat next to it.
  • Free Floating
    • Yes, could anchor also.
  • Scalable
    • Is small enough for one family. The shape could scale to much larger sizes. Geodesic domes scale well.
  • Standards
  • Mobile
    • Will move through the water easier than most seastead designs but not as easy as a ship.
  • Draft
    • Very shallow draft for a seastead if the hanging ballast is winched up. If the waves were small as you approached a harbor it should be safe to winch up the hanging ballast. Could lower the ballast onto the bottom in a harbor, keeping some tension, making a simple tension-leg structure.

Experiments

Ballhousemodel.jpg Ballinfo.JPG

Used a 36 cm (14.2 inch) diameter buoy with 20 lbs of steel weights. At 1:25 scale this is about a 30 foot sphere. These videos should have been slowed down by a factor of 5 but are really slowed down by a factor of 4.

The first video is with about 4 feet of rope in waves that are a few inches (6 inches simulates 12.5 feet). This was shot near the end of the pier in Island Harbor Anguilla. This swings back and forth too much. Experiments on later days with longer ropes work much better.

<youtube v="u6U8tc7wp2s" />

Experiments 2 - deep water in Shoal Bay

The next 4 videos were shot on Aug 28, 2008 after swimming to deep water on the other side of the inner reef at shoal bay. I estimate the biggest waves are simulating 50 foot waves, which is bigger than I expect to ever see if we use migration.

The first video below is with the 20 lbs of weight tied close below the ball, maybe 1/2 foot of rope.

<youtube v="8Ad1lzixLfg" />

The rest of the videos on this day are with 23 feet of rope between the ball and the 20 lbs, in the same big waves as the video above.

<youtube v="HqZY7LYdLHk" />

During this next video I was drifting closer to shallow water so stopped early. There are a couple times when the ball seems to tilt a bit. It may be because the weights had touched bottom and the tension on the rope was reduced. But either way, this ball is still doing a good job of keeping the topside up in really large waves.

<youtube v="TUUmPPDn_j0" />

This next shot is fun because there is a jellyfish in the upper-right part of the shot. It is also interesting because in about the middle of the clip we get the underwater view of a breaking wave hitting and tipping the model.

<youtube v="fd_9ry_oJXI" />

Experiments 3 - deep water outside Island Harbor

The videos in this section were shot from a kayak on Aug 31, 2008. I took the net off the buoy and put some black lines on to make it easier to see how much the buoy tips with the waves. These were shot outside the reef north of Island Harbor Anguilla. The kayak rudder does not work when you are nearly standing still so peddling did not work so well. I could not use the paddle while keeping the camera aimed, so that was not good either. I tried giving my 4 year old the camera, but in hindsight, I should have explained the goal of keeping near the buoy and had him use the paddle while I did the camera. Anyway, these are mostly not close enough to see how well my water-level with a new block inside to dampen the sloshing is working, but sometimes. I have since realized that I could take apart the paddle and use half in one hand as an oar to control my direction while my legs provided power. So I think I can stay closer to the model next time.

I would call these simulated 40 foot waves, which is more than I think we will see if we use migration. Used the same 23 foot rope used in the Shoal Bay experiments.

<youtube v="GepQjK4uVJ8" />

<youtube v="lMhj77_fkW8" />

<youtube v="ZtL4JhVIEzY" />

In this next video we got close enough at times to really see the red water moving around. Even though the buoy is staying very level, the waves are accelerating it sideways and so causing the red water to move around. Now these are simulated hurricane conditions, and not normal weather. If you were in a small bunk with sides on it or in a seat with a seatbelt, you would be fine.

<youtube v="_0_ph-K-lL8" />

This next video was shot by Teryn, my 4-year-old, while sitting on the front of my kayak. The a lightweight boy on the front moves up and down more than a big dad in the middle. But it is still interesting.

<youtube v="pQ3iqbJwt3g" />

Full Scale Ball House in Plastic

I think it would be reasonable to make a 30 foot ball out of HDPE plastic. If this has "carbon black" in it the sun won't hurt it. I am thinking that if the plastic was 1 inch thick it would be plenty strong enough. A ball is a strong shape as the sides sort of have arch type support in both directions. Think of how strong an egg is when you try to squeeze it in your hand.

The density of HDPE plastic is just under that of water. If you buy the HDPE pellets by the ton, the price is about $1/lb. So a 30 foot ball that was 1 inch thick might weigh about 15,000 lbs and cost about $15,000 for the raw plastic. It may even be that 1/2 inch is thick enough. This would be a very low cost seastead.

You could have an inner and outer mold connected by bolts to hold the right spacing between the molds. After pouring you take out the bolts and the molds come apart in sections. Then you plug the holes in the ball with HDPE plugs (fusion weld these in).

Another possibility is related to how they wind on the plastic for large corrugated plastic pipe. We could go around and around making a ball instead of a pipe. Maybe we put on a two inch wide strip of plastic each time we go around. Might take a machine most of a day to make a ball but this is not bad.

My favorite way is to have a big ball rotomold out of aluminum. This 30-foot aluminum ball would be set on some wheels so it could be rolled in different directions. Probably 3 or 4 wheels with 1 or 2 that can turn and an electric motor on one or more. If we put the HDPE pellets inside, start rolling the mold, heat it up, and keep rolling the mold while it cools down we can have a big plastic ball when it is done. This "rotomolding" is how most kayaks are made so easily that they can sell as little as for $240. The mold would have to come apart in sections so we could get the plastic ball out.

Looking for large roto-mold examples I found Ace Roto-mold/ Advanced Tank Technologies makes tanks up to 10,500 gallons which is 142 by 177 inches (14.75 feet). Found a Rock-N-Roll machine that can do 6.5 meter boats (21 feet).

There is info about roto-molding online.

There are lots of places that sell stainless steel spheres or hemispheres that could be used for molds. Shipping gets hard above 8 feet diameter, but they can be made whatever size you want it seems. With two hemispheres you could make plastic balls using the rotomold method (though some work will need to be done to figure out how to heat and roll the mold). Could start plastic ball making experiments using 12-inch steel hemispheres from shopwagner.com for $37 each.

Full Scale Using Ductal

The Ductal concrete blend is very strong, waterproof, and lasts well in salt-water. This could work well for making a larger model or full scale BallHouse.

Low Cost Design Champ

The ball does not heave up and down like the pipes/cylinders/spars do so it would not require heave plates. Having the ballast rope attach to the bottom of the ball provides enough stability, no truss is required. The experiments show that this design does well even in 50 foot waves. A ball shape is strong for the amount of material, whatever that is: plastic, concrete, aluminum, or steel. So I think for small single family seasteads that are safe on the open ocean that this is the low cost design champ. If you think there is anything cheaper please post in the discussion for this page or on the Engineering forum.

I think this ball could even be made smaller, like 20 feet diameter, or even 15 feet diameter, and still be very stable and safe. Because it floats up with the waves, and moves away and so kills breaking waves, it can be safe in waves higher than it is. It would be easier to get plastic to work for a 15 foot diameter ball than a 30 foot diameter ball. The internal volume would still be better than many boats people live on. At this size it could be cheaper for a family to buy a Ball House than to pay to be smuggled into the USA.

Chinese Survival Pods

Some Chinese worried by the movie 2012 built ball shaped survival pods. These were for sale for $50,000 before the Mayan end of calendar and one expects much cheaper after that.

Discussion on Forum

This proposal has been discussed on the forum.